HITESHKUMAR PATEL

• New project management
• Installation of Communication Equipment
• Maintenance of telecommunication equipment and maintenance
• Software and Hardware troubleshooting

• Attending breakdowns
• On-site Maintenance on demand Basis.
• Improvement and Installation of Equipment in Plants
• Maintenance of all types of pumps and motors
• Maintenance of plating robots like auto-operating machine
• Plating and passivation line operation and maintenance
• Maintain all store items, order, and stock
• R O Plant operation, maintenance, and implementation
• Attending utility side problems and PM/PDM work.
• Put in replacement parts and components as well as entire systems.
• Evaluated heating and ventilation systems to gauge issues or concerns.

• Conducted regular preventative maintenance in the plating plants and robots to minimize failures and delays.
• Inspection and repair of daily used equipment to minimize breakdowns and system failure,
• Drafted and submitted maintenance reports to a supervisor.
• Conducted inspections of control panels and electrical wiring to identify problems.
• Ordered maintenance stocks appropriately to maintain service continuity.
• Evaluated heating and ventilation systems to gauge issues or concerns.
• Diagnosed and repaired faults affecting the proper performance of heating systems.
• Cleaned and tidied work sites after job completion.

Electrical Work Experience

• Attending breakdowns.
• Attending utility side problems and PM/PDM work.
• Operation and Maintenance of COE conveyor (make-VINAR & PRAJA), EMS hoists (make-DEMAG & LOAD STAR), and burners (make-ECLIPSE).
• Looking after PMCC panels, MCC panels, EMCC panels, Lighting panels, Air Circuit Breaker
• Looking after Flameproof Motors, Non-Flameproof Motors, Flameproof lighting fitting, and lighting jobs
• Modification work of all panels with control wiring including plc as required or implemented.
• Basic SLC/PLC Troubleshooting and maintenance in Paint shop Equipment like Painting Robot, Elpo EMS, Ovens, Burner, And any types of Automation panels.
• Basic PLC troubleshooting in all the areas of assembly lines.
• Basic Knowledge of RS Linx, control net, device net & its troubleshooting.
• Operation and maintenance of lighting distribution panel, Pumps, Motors, and LPG leak detectors, Manual call point panel.
• Operating and maintenance-related activity in the paint shop, Pre-treatment line, conveyor, Oven Burner, and EMS system.

Mechanical Work Experience

• Attending breakdowns.
• Attending utility side problems and PM/PDM work.
• All types of Pumps, like KSB, Grundfos, etc. Single Mechanical seal type pump and Double Mechanical seal type pumps with Gland type Single stage and Multistage pumps, with vertical and horizontal type pump maintenance.
• Application type pump Graco company double stock Reciprotector drive, diaphragm type double stock pumps, CCV (color change valve starter, Graco paint line instillation with connectors, etc.
• Good knowledge of bearings like Single Roller bearings, double Roller bearings, Single Ball bearings, Double Ball bearings, Plan bearings, Centrifuges bearings, Four contact angle bearings, etc. With maintenance and replacement.
• Worked on centrifuge type Fan, like Supply fan, Exhaust fan plant ventilation system on maintenance with Fan Balancing. Knowledge of all types of Coupling like Love jaw Coupling, pin Bush Coupling, Tier Coupling, Chain Coupling, Gear Coupling, Fluid Coupling, etc.
• Worked on AC System Condenser unit with Chiller unit on Operating with maintenance.
• Good Knowledge of Eclipse Burner to LPG /LNG Fluid operating used on Oven. Do maintenance and Troubleshooting.
• Worked in Chain On Edge Type Conveyor with Maintenance
• Knowledge of Power Transfer using equipment like All types of V-belts, Coupling, Gearbox, and Chain with good knowledge of Taper lock Pulley with selected Pulley requirements of Equipment RPM with maintenance.
• Worked in the Air to operate a Pneumatic cylinder with a selected system type of cylinder and maintenance and Knowledge of Hydraulic systems and troubleshooting with maintenance.

• Oversaw daily spot welding activities in the car manufacturing environment.
• Working in the car manufacturing plant.
• MIG welding and Spot welding.
• Door assembly, Hood assembly, Bumper assembly.
• Spot welding With pneumatic and hydraulic Fixtures in the cars.
• Inline spot welding works 10 Cars per Hour.
• PM Activity on a daily basis,
• Routing Maintenance on a weekly basis,
• Improvement and suggestion work in non production hour,
• Documentations with Chassis no until quality check out from Body shop.

• Boiler light-up operation
• Monitoring of boiler & related equipment daily base
• Worked in D.M Water Plant Monitoring and Maintenance.
• Plant Maintenance in R.O Plant
• Planning and maintenance of processes equipment & tooling
• Furness burner and temperature sating and monitoring
• Finished on-the-job training within set deadlines.
• Attended necessary training and completed assessments.